clifton plumbing logo

(973) 858 5005

24/7 Customer Support

Leaking Faucet | BJC Clifton Plumbers

How to Fix a Leaking Faucet: Quick & Easy Tips

When a faucet develops a leak, it is often because one of its components has been worn out and no longer functions properly. The way in which the leak in the faucet is fixed is dependent on the location of the leak as well as the mode in which the faucet is operating. Compression, the disc, the cartridge, and the mechanism are the primary categories that are used to differentiate between the many types of faucets that are available.

Before you make an effort to repair a leaking faucet, you need to determine the kind of faucet it is. This will allow you to better understand how to do the essential maintenance and repairs. Before you can get started, you are going to need some of the items listed below:

When you get a broad faucet, the valves will often be concealed in a manner that is more aesthetically pleasing. The thread on the majority of valve assemblies is rather fine, therefore you should attempt unscrewing the trim piece. Under each knob, there is a screw that secures the handle to the stem of the product. You will need to loosen the handle before you can gently remove it. It might be difficult to remove the handle from the stem of the faucet at times. Applying WD-40 will help get this component to move.

It is normal to be able to view the stem when the packing nut has been loosened. You are going to want to remove this component. At this stage, the way you use various faucets will be distinct from one another. For instance, the stem of certain valves may be removed by simply popping it off, whereas others need a twisting motion. Carefully remove everything from the room. You don’t want to put any of the pieces in danger of breaking since it might make the problem with the leaking faucet much worse.

If your sink is less than 25 years old, there is a good chance that it still contains the original cartridge inside of it. The chairs are clearly worn out since their power has been cycled on and off for the last 25 years, which has caused their power to be cycled on and off. Utilizing a set of channel locks, make an effort to remove the cartridge in a vertical direction. Because scale has built up over time and stuck the cartridges in place, it may at times be difficult to remove them. This is due to the fact that scale has built up over time. If you give the cartridge a little shake before tugging on it, it ought to come out on its own without your assistance. In the event that you are unable to remove it, it is recommended that you get in touch with a skilled plumber. It is possible to remove the cartridges from the printer with the assistance of various tools.

Equipment of the Trade

In order to reduce the amount of time wasted, check that you have all of the necessary equipment. In a perfect world, you would have:

At this point, everything should continue to function normally. Take a look at the washer and the O-ring that is located within the valve seat. It is common for water to get inside when this component is damaged or when the seal begins to wear out. You are going to remove the washer and then install the replacement washer in its place.

Because of how easily this component may get damaged, you will also need to replace the O-ring. Before you replace your O-rings and washers, you should make sure that they still fit properly. Whether you are unsure about any of these things, check the seat to see if the flat washer will fit between the edges of the seat. It’s possible that you’ll need to purchase a different size.

If you are unable to locate an O-ring in the appropriate size, you should bring it to a hardware shop to ensure that it fits properly. Examine the shape of the seat’s sides to determine whether or not they conform to a cone if you are unsure. After that, you will be able to purchase the appropriate O-ring. You are not required to bring in your old O-ring to be replaced at the hardware shop. You might, instead, purchase a set of O-rings in a variety of sizes. Although it may add a few dollars to the total cost, it will be well worth it to ensure that you obtain the appropriate size.

Setting It Up

After you have disassembled your faucet and put it back together, you will need to check to see that it does not leak anymore after you have finished. If it does, it is possible that a damaged O-ring is not the source of the problem. The second thing that you should often check for is corrosion on the valve seat.

This occurs when it has been unclean for an extended period of time, which causes a leak to form closer to the spout of the faucet. In the event that this does not cure your leaking faucet, the problem may be caused by plumbing issues, worn-out seals, or loose components. In the event that none of these solutions work, you may have no choice but to bring in the heavy guns and hire a plumber.


In the case that this does occur, you will need to find the location where the water first enters the house in order to be able to turn it off. Be aware of the fact that if you close the water valve, everyone in the home will start screaming since there won’t be any water. Nevertheless, in the process of fixing anything, it will inevitably become essential to do so at some point.

For professional plumbers in Elizabeth, NJ call today.